Top 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Top 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Blog Article

Don't take too lightly the forklift at the office. If the procedure is bad, there will certainly be serious accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead could not be discovered, leading to a rolling mishap.
Case 2: In order to maintain the balance of the forklift when lifting heavy items, the staff members utilized their body weight as the weight, which virtually triggered casualties.
Situation 3: The width of the forklift cargo exceeds the allowed size of the path and hangs on the roadside shelf, which almost creates an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Instance 5: The forklift motorist did not discover the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the workers illegally, the forklift driver does not put on the safety belt, the forklift lifter falls and the vehicle driver is squashed when the forklift rolls over.
Instance 7: The forklift vehicle driver did not use a seat belt and dropped from the lorry when it surrendered and was squashed.
Forklift operation ought to take note of these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards begin.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be secure before beginning.
3. When the forklift starts with a tons, the driver needs to first validate that the load is secure and reputable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When getting in and leaving the job site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork needs to not be raised too expensive, which will certainly influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving setting prior to driving. .
4. When transforming, if there are pedestrians or cars close by, the driving signal must be released first. High-speed sharp turns are forbidden. High-speed doglegs will certainly cause the car to lose side security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the flame and slide, and it is prohibited to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and have to maintain a particular safety and security range from the vehicle in front. .
7. When the forklift is running, the load must remain in the most affordable placement that does not prevent the driving, and the gantry needs to be properly slanted back. The lots will not be elevated other than when piling or filling. .
8. The elevation of the lots need to not obstruct the motorist's sight. In special situations, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced speed when entering the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to depend on the fork to hold products and play a balancing duty. .
12. If troubles are discovered, they will be fixed and reported in a prompt manner, and they will certainly never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the range between both forks ought to be adjusted as required to make the load of both forks balanced and not skewed, and one side of the product ought to protest the rack. .
2. It is forbidden to collaborate with a single fork or make use of a fork top or pull. In unique scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift must be braked with the brake. .
4. The rate of the automobile should be sluggish and steady. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled items and hurt people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it needs to be noted that the fork idea should not touch other items or objects. The tons should be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted forward somewhat when the tons is decreased to allow for simple positioning of the load and extraction of the forks. .
6. It is prohibited to fork items at broadband and collide with difficult items with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is forbidden, and it is banned to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to utilize the brake inertia to slip, put, round or roll items. .
10. It is not permitted to make use of forks to select, transform pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake deal with to dead or depress the emergency brake switch.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the chauffeur does not leave the car's line of vision and does not exceed 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature Stand-on Electric Pallet Stacker level are regular.
5. After the forklift is running, the outside leakage should additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the vehicle;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope should be sluggish and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move on, if they experience huge or heavy products and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Single fork operation is not permitted.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to get the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It is not permitted to use inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not allowed to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on Electric Forklift Truck for Warehouse inclines
.
Vehicle parking is not allowed under the list below problems.
1. Contours, slim roads, railway crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same length as the obstacle must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844